|
Electrical Components |
Confused how to electrify your dolls' house? Don't be. Here is your free guide to "Electrifying your dolls's house the easy way".
Geppetto The Toymaker can supply a range of Cir-Kit Concepts electrical components for the DIY enthusiast. Please enter enter the details on your order form and post to Geppetto today.
Picture to be added |
Save money
with this easy to use electrification kit for your dolls house.
Connect four wires only. Complete with simple instructions on how to
electrify your dolls house with ease. Available with or without
switch.
Without switch Price £1.50 + p&p With switch Price £2.50 + p&p |
 |
This lead-in
wire may be used for those installations requiring the convenience of
total dollhouse on/off power control. (Eliminates need for unplugging
lead-in wire from dollhouse to disconnect power.)
Price £4.40 + p&p |
 |
The Bridging
Cord is used for interconnecting two tape mounted CK1007 Junction Splices
(not included). Its use provides an extremely easy to install and low
profile connection when completed. The connecting cords are 18" long and illustrated instructions are provided with each package. Price £3.18 + p&p |
 |
The
remarkable Cir-Kit Concepts' ceiling canopy makes any chandelier removable
with just a "twist of the wrist". A quarter turn clockwise for
installation and a quarter turn back for removal. Nothing could be
simpler! And the rich plating will compliment even the most ornate of
hanging fixtures. You're sure to agree it's the easiest method yet for
installing ceiling chandeliers. Complete instructions included.
Price £3.99 + p&p |
 |
At last, an
easy solution to one of the most vexing miniature wiring problems; sconce
installation. Invariably this task has meant the grooving of walls or the
placement of sconces on inside walls only. With the Sconce Adapter these
problems are simply a bad memory. Installation can now be made on any
wall; exterior or interior. Using the sconce adapter, a sconce may be installed on either a vertical or horizontal tape run and may be rotated up to 30 degrees in either direction for perfect alignment. The adapter ring is fully brass plated making it suitable for even the most ornate of wall fixtures. Complete step-by-step instructions, with detailed illustrations, are included in each package. Special spring-loaded eyelets are included with each adapter. These eyelets grip the adapter plug and ensure a tight fit against the wall. Price £5.58 + p&p |
 |
This "to
scale" dollhouse outlet is, to our knowledge, the smallest working
outlet ever made, measuring a mere .414" high by .3" wide by
.13" thick. And installation couldn't be easier. Simply place over
the tape run at the desired location and pound in. The outlet nails are imbedded diagonally, allowing the outlet to be mounted vertically regardless of whether the tape run is vertical or horizontal. By using the CK204 Test Probe to locate the tape run, the outlet can be installed even after wallpapering. Each outlet is constructed of tough, white plastic with tapered edges to achieve an authentic outlet look. The double set of holes will accommodate two CK1004 or CK1004-2 plugs and provides a convenient means of electrifying any miniature floor or table lamp. Each package also contains 1/4" brass brads for use as marker pins when wallpapering. 600 ma current rating. Price £1.76 + p&p |
 |
Give a
polished brass look to all your outlets. These bright and heavily engraved
covers will provide a rich and finished appearance wherever they are used.
The double holes allow ample space for inserting and removing either type
of CK1004 plug. Simply place over outlet and press in place. Price £1.60 + p&p |
 |
The "to
scale" CK1004 Plug is made to work with the CK1003 Outlet and may be
attached to the bulb wires from any lighting fixture. To make an
electrical connection, stripped lamp wires are simply inserted into small
holes in the side of the plug and the supplied pins pushed in from the
front. Since the plug is not permanently attached to the wires it may be
reused time and time again, a real plus! The plug is made of hard, white
plastic and extends less than 1/4" when plugged in. Assembly
instructions included. 600 ma current rating. Price £1.76 + p&p |
 |
The "to scale"
miniature slide switch is the first of its kind ever made in the
electronics industry. Most standard models are equipped with a protruding
toggle to allow electrical operation. A close look will reveal that the
switch has no such toggle-like feature. Instead, it is designed with a
smooth sliding outer body to achieve the "on/off" operation. Why
this departure from conventional logic? Ease of installation. Its rugged
construction makes it ideal for use in even the hardest of woods.
Placement has now become as simple as installing our famous CK1003
"pound-in" outlet. The complete and fully illustrated
instructions included with each switch ensures a successful installation
every time. Each package also contains 1/4" brass brads for use as
marker pins when wallpapering. 600 ma current rating.
Price £3.99 + p&p |
 |
Add a
finishing touch to all your switches. This distinctive brass plate simply
snap fits over the switch to give it a rich and decorative appearance. The
protruding toggle enhances the "on/off" operation and provides
an added look of realism. Price £1.60 |
 |
The
size of our miniature two-conductor "zip" cord (.021" by
.047") makes it one of the smallest two-conductor cords to be found
anywhere. Each wire is a 32 gauge stranded conductor and its soft
flexibility makes for easy handling and forming. Once started the wires
may be separated by merely pulling them apart. Stripping is accomplished
with the fingernails. Made with white plastic covering, 25' long. Price £3.72 + p&p |
| Picture not available | 12 volt
Micro-Flame Bulb with varnished wires.
Price £2.10 |
Cir-Kit products - text and images courtesy of Cir-Kit Concepts
Maker of Quality Fun
Hand made toys & bespoke dolls
houses and miniatures